Savage model 24 trigger guard
![savage model 24 trigger guard savage model 24 trigger guard](https://www.gunpartscorp.com/Pub/schematic/Savage_24S_schem.jpg)
You will need a vice, a diamond stone, a spring steel wire that measures. Using this method its fairly easy to get a 2 pound safe pull with little or no creep and reduced overtravel. This is how Savage trigger work is performed in my shop. In any event, please be safe and triple check the operation after any modifications. If you decide to adjust your own trigger, you do so at your own risk with no liability from the author or the website operators. It should only be performed by qualified gunsmiths. Adjusting a trigger is a serious and potentially dangerous activity. treat all weapons as if they are loaded.īy Claude Gatewood NOTE: These procedures are to be used at your own risk. Use dry lube (moly-powder) on the sear for lubrication and dry fire the rifle to break in the settingĪnd get used to the new lighter pull weight. SLAM FIRES AND OTHER TYPES OF ACCIDENTALĭISCHARGES ARE PROBABLE IF THIS GENERAL RULE IS IGNORED.ħ) Use lock-tite to set all of the screws adjusted in your project. If the rifle does not pass this test, re-check your safety adjustment and sear engagement settings.Ħ) To set the trigger for overtravel, turn screw #4 with the bolt un-cocked.ĭO NOT ATTEMPT TO SET THE SAVAGE FACTORY TRIGGER BELOW THREE POUNDS. The rifle’s safety should be tested wile unloaded and while aggressively cocking the bolt handle and also bumping the rifle butt on the floor to attempt to make Adjust the safety screw to slightly touch the safety bar but not interfere with it’s operation. Once this is achieved, re-cock the action and adjust the safety screw.ĥ) Adjustment of the safety screw should be done with the safety “ON”. To re-set the sear engagement, you must turn the screw back in a It is also important to understand that thisĪdjustment is usually not often necessary, but require the trigger be removed from the action in order to access the top of the screw.Ĥ) Screw #2 should be loosened with the bolt cocked. The safety lever should have no up/down (play) movement. Opposing notches in the screw head to secure the adjustment.ģ) Screw #1 is to adjust the smooth travel of the safety lever. Setting the spring to lightly can prevent proper trigger recovery/re-engagement. Spring in order to insure proper function.
Savage model 24 trigger guard series#
This is a small diagram of the Savage model 110 Series (which includes 10/12 type short action rifles and 110/112 long action rifles) trigger group.ġ) Remove the rifle from the stock by removing the action screws in front of and behind the trigger guard.Ģ) Minor adjustments to weight of trigger pull can be made by adjusting the tension on the trigger spring with Screw #5. Service is well worth the peace of mind in that you’ll have a safe rifle. The small amount of money you’ll pay a quality gunsmith for this
![savage model 24 trigger guard savage model 24 trigger guard](https://www.picclickimg.com/d/l400/pict/163270780419_/Savage-Stevens-Model-94-Trigger-Guard.jpg)
Anyone who hasĪny reservations about making these adjustments should seek the assistance of a qualified gunsmith. Use Lock-Tite thread locker in order to secure any adjustments made to your rifles trigger mechanism. I was lucky enough to attend the Savage Law Enforcement Armorer’s School and think theseĭirections are easy enough to follow safely. Use caution in following these directions and never use liveĪmmunition to test the function of any rifle’s safely mechanism. It is important to keep in mind that setting a trigger too lightly can and most often does result in accidental discharges and slam fires (round discharged fromĬlosing the bolt on a live round) as well as safety induced discharges from improper trigger adjustments. Triggers should only be performed by mechanically inclined individuals who have a good understanding of mechanics and more than your average dose of common Those desiring a lighter trigger than three pounds should consider a good after market trigger like the Sharp Shooter’s Supply or Rifle-Basix triggers. Savage rifles can be dry-fired without any adverse effect on the rifles.
![savage model 24 trigger guard savage model 24 trigger guard](http://www.fourten.org.uk/savage_24_exploded.gif)
Lubricating the sear with a dry moly powder and dry firing the rifle 40-50 times will smooth out (break-in) the sear and provide The Savage trigger should not be stoned, or filed down at the sear It has adjustments for lightness of pull, trigger creep, over travel and safety engagement. The author is Ken Russoīefore we begin, you should understand that the Savage Factory Trigger in 110 series rifles is a simple yet effective trigger capable of holding a setting to about three Adjustment of the Savage 110 Series TriggerThis is great info that I pulled from the web.